您现在的位置:首页 > 技术支持技术支持

ADIADXL362微功耗三轴MEMS加速度计解决方案

发布时间:2018-09-29 06:34:22  来源:大电流电感厂家   查看:

ADI公司的ADXL362是微功耗三轴MEMS加速度计,数字输出,加速度范围为±2/±4/±8 g, 工作电压1.8V-3.3V,电源电压2V和100Hz输出数据速率时的功耗为2μA,运动触发叫醒模式的功耗为300nA,器件提供12位输出分辨率,8位格式的数据,在±2 g范围的分辨率为1 mg/LSB,主要用在助听器,家庭保健设备,运动使能电源开关,无线传感器和运动使能计量设备.本文介绍了ADXL362主要特性, ADXL362功能方框图以及评估板EVAL-ADXL362Z主要特性和电路图.

ADXL362:Micropower 3-Axis MEMS Accelerometer: Digital Output, ±2/±4/±8 g Range

The ADXL362 is an ultra-low power 3-axis MEMS accelerometer that consumes less than 2 μA at a 100 Hz output data rate, and 300 nA in motion-triggered Wake-Up Mode.

Unlike accelerometers tha贴片电感生产厂t use power duty cycling to achieve low power consumption, the ADXL362 does not alias input signals by undersampling; it samples the sensor’s full bandwidth at all data rates.

The ADXL362 always provides 12-bit output resolution; 8-bit formatted data is also provided for more efficient single-byte transfers when a lower resolution is sufficient. Measurement ranges of ±2 g, ±4 g, and ±8 g are available, with a resolution of 1 mg/LSB on the ±2 g range. For applications where a noise level lower than the ADXL362’s normal 550 μg/7Hz is desired, either of two lower noise modes (down to 175 μg/7Hz typ) may be selected at minimal increase in supply current.

In addition to its ultra-low power consumption, the ADXL362 has many features to enable true system-level power reduction.

It includes a deep multimode output FIFO, a built-in micropower temperature sensor, and several activity detection modes including adjustable-threshold sleep and wakeup operation that can run as low as 300 nA at a 6 Hz (approximate) measurement rate. A pin output is provided to directly control an external switch when activity is detected if desired. In addition, the ADXL362 has provisions for external control of sampling time and/or an external clock.

The ADXL362 operates on a wide 1.6 V to 3.6 V supply range, and can interface, if necessary, to a host operating on a separate, lower supply voltage. The ADXL362 is available in a 3 mm × 3.25 mm × 1.06 mm package.

ADXL362主要特性:

Ultra low po插件电感wer

Power can be derived from coin cell battery

1.8 μA @ 100 Hz ODR, 2.0V supply

3.0 μA @ 400 Hz ODR, 2.0V supply

300 nA motion-activated Wake-up Mode

10nA Standby Current

Built-in features for system-level power savings:

Adjustable-threshold sleep/wake modes for motion activation

Autonomous interrupt processing without need for microcontroller intervention, so the rest of the system can be turned off completely

Deep embedded FIFO minimizes host processor load

Awake state output enables implementation of standalone motion-activated switch High resolution of 1 mg/LSB

Low noise down to 175 μg/@Hz

Wide supply and I/O voltage ranges: 1.6 V to 3.6 V

Operates off 1.8V to 3.3V rails

Acceleration sample synchronization via external trigger

On-ch薄膜片式电感器ip temperature sensor

SPI digital interface

Measurement ranges selectable via SPI command

Small and thin 3 mm × 3.25 mm × 1.06 mm package

ADXL362应用:

Hearing aids

Home healthcare devices

Motion-enabled power save switch

Wireless sensors

Motion-enabled metering devices

图1. ADXL362功能方框图

ADXL362评估板EVAL-ADXL362Z

The EVAL-ADXL362Z is a simple breakout board that enables easy connection of an ADXL362 micropower, 3-axis, digital-output MEMS accelerometer into an existing system. Due to its small size, the EVAL-ADXL362Z has minimal effect on performance of the system and of the accelerometer, and thus it is ideal for evaluation of the ADXL362 in an existing system. Note that the ADXL362 must be communicated with digitally via SPI. No processor is included with the EVAL-ADXL362Z; firmware must be supplied externally by the user. Some sample firmware is available at the link below:

The EVAL-ADXL362Z-MLP is a complete system for real-time evaluation of the ADXL362 micropower, 3-axis, digital-ouptut MEMS accelerometer. This system is accompanied by a graphical user interface (GUI) that facilitates evaluation of parameters such as power consumption, temperature coefficient, noise, and more. The system consists of a motherboard and a satellite board. The sensor is housed in a socket on the satellite board, enabling evaluation of multiple parts using one evaluation system.

浅析基于MSP430心肺听诊技能训练系统设计方案基于MSP430心肺听诊技能训练系统针对现代医学模拟教学的发展,改变过去用射频和特制听诊器来模仿心肺听诊过程,在操作上更逼真临床真实环境。以低功耗的MSP430为核心,并在模型人上安装27个专用设备来

ABB变频器应用误区及应对策略 误区一:在变频器输出回路连接电磁开关、电磁接触器在实际应用中,一些场合需要使用到接触器进行变频器切换:如当变频故障时切换到工频状态运行,或是当采用一拖二方式,一台电动机故障,变频器转向拖动另一台电动

基于FPGA高阶FIR滤波器的实现摘要:从FIR数字滤波器的基本结构模型出发,分析了FIR滤波器的设计思路及具体实现方法,详细介绍了FIR滤波器的分布式算法(DA)结构。通过分析计算,得到普通DA结构实现高阶滤波器会消耗大量的查找表资

CopyRight2014
大电流电感 | 大功率电感 | 扁平线圈电感 注塑加工厂