脉宽调制直流电动机控制电路

脉宽调制直流电动机控制电路 Pulse Width Modulation DC Motor Control

Often, people attempt to control DC motors with a variable resistor or variable resistor connected to a transistor. While the latter approach works well, it贴片电感插件电感器 generates heat and hence wastes power. This simple pulse width modulation DC motor control eliminates these problems. It controls the motor speed by driving the motor with short pulses. These pulses vary in duration to change the speed of the motor. The longer the pulses, the faster the motor turns, and vice versa.

Schematic

Parts

Part差模电感器
Total Qty.
Description
Substitutions

R1
1
1 Meg 1/4W Resistor


R2
1
100K Pot


C1
1
0.1uF 25V Ceramic 东莞电感器Disc Capacitor


C2
1
0.01uF 25V Ceramic Disc Capacitor


Q1
1
IRF511 MOSFET
IRF620

U1
1
4011 CMOS NAND Gate


S1
1
DPDT Switch


M1
1
Motor (See 塑封电感Notes)


MISC
1
Case, Board, Heatsink, Knob For R2, Socket For U1

Notes
1. R2 adjusts the speed of the oscillator and therefore the speed of M1.

2. M1 can be any DC motor that operates from 6V and does not draw more than the maximum current of Q1. The voltage can be increased by connecting the higher voltage to the switch instead of the 6V that powers the oscillator. Be sure not to exceed the power rating of Q1 if you do this.

3. Q1 will need a heatsink.

4. Q1 in the parts list can handle a maximum of 5A. Use the IRF620 for 6A, if you need any higher.

平面变压器厂家 | 平面电感厂家

[充电器]如何修改充电器末期的恒压值？各位师傅：请教一个问题：我手头有一台大型充电机，是给铅酸电池组充电的。 该充电机的电流最大可到100A,恒压值是32V。 我现在想修改这台充电机以对动力型锂离子电池组充电。      锂离子电池组的满充电压是28V，现在希望在大型充电机的正极回路中加入一些装置，将充电末期的恒压值限定在28V。 请教各位师傅，该如何设计方案啊？（备注：

[开关电源]反激电源带感性负载+阻性负载启动不最近在测试一款输入300VDC，输出正负15V的反激电源，输出功率20W，其中正15V要求能带载1.3A，负15V要求能带载0.1A，用的芯片是TNY280，反馈是常见的TL431+PC817组合方式，测试过程如下：一、正15V带1.3A电阻负载，负15V带0.1A电阻负载，可以带载启动，见图1；二、正15V带载0.5A电阻负载+3个并联风扇（15V/0.2A），负15V带0.1A电阻负载，发现带载启动出现打嗝

FPGA牛人的经验分享这里我谈谈我的一些经验和大家分享，希望能对IC设计的新手有一定的帮助，能使得他们能少走一些弯路!在IC工业中有许多不同的领域，IC设计者的特征也会有些不同。在A领域的一个好的IC设计者也许会花很长时间